LIGHT REACTIVE WELDING HELMET with AIR RESPIRATORY SYSTEM

£389.99 Ex VAT

SKU: FS-ARS-916H Categories: , , Tag:

Description

LIGHT REACTIVE WELDING HELMET with AIR RESPIRATORY SYSTEM

The Parweld XR936A combines the Parweld XR936H Light Reactive Welding Helmet with a clean air respiratory unit to provide the user with added protection against welding fume, dust particles and aerosols.

Clean Air Unit
The Parweld powered air purifying respirator (PAPR) provides a steady stream of clean air into the welding mask. The air is fed into the helmet above the welder’s head and exits below the chin. The air stream combined with the positive pressure created within the helmet prevents contaminated air entering the breathing zone.

Portable and Lightweight
The main unit and battery pack are carried by the user on a support belt around the waist, which is connected to the welding helmet by a lightweight umbilical hose.

Adjustable Air Flow
The air flow rate can be adjusted from 150 to 220lpm by means of a push button panel with led indication. In the event of a flow rate falling below the
minimum required level to give protection the blower unit will automatically increase the fan speed to compensate. If the minimum flow rate cannot be
achieved then an alarm will sound so that the operator can leave the work area safely, if the first alarm is ignored the unit will then start to vibrate and increase the volume of the alarm. The Li-ion battery pack is rechargeable and will operate from 6 to 15 hours continuously, dependant on operational mode.

Pre-filters and Filters
The XR936A uses a 2 stage filter process, the main P3 filter gives the required essential isolation against welding particles, smoke and dust providing the user with a protection factor of 20. The standard filter can be complemented with a pre filter which removes large dust particles and so extends the life of the main filter.

Conforms to International Standards
The XR936A Air Flow System is independently certified to BS EN 12941 TH2P R SL. The XR936H Light Reactive Welding and Grinding Helmet is independently certified to BS EN 379:2003+A1:2009, BS EN 175:1997

Features

ATURES • Portable and Lightweight
• Protects Against Dust Particles, Solid and Liquid Aerosols and Smoke
• Constant Filtered Air Flow
• Lightweight Li-ion Removable Battery
• Audible, Visible and Vibration Warning Alarms for Low Power, Low Air-flow and Blocked FilterXR936H Light Reactive Welding Helmet
• Automatic Light Adjustment from light to dark in 1/30,000th of a second
• Shade Control from DIN5-13
• Variable Sensitivity
• Grinding Mode
• 3 Lightening Delay Settings
• Full Face Coverage
• Automatic Power On/Off
• Battery Life Expectancy 6 Years
• UV/IR Protection up to shade DIN 16
• 24 Months Warranty (6 Months on Battery)
STANDARDS BS EN 379, BS EN 175, EN 166
VIEWING AREA 100mm x 52mm / 3.94″ x 2.05″
UV/IR PROTECTION Permanent Shade DIN16
LIGHT STATE DIN Shade 4
DARK STATE DIN Shade 5 to 13 Variable
POWER SUPPLY Solar cells with replaceable batteries
POWER ON/OFF Fully automatic
SWITCHING TIME LIGHT TO DARK 1/30,000 Seconds
SWITCHING TIME DARK TO LIGHT 0.1-1.0 seconds (internal variable)
OPERATING TEMPERATURE -10°C to +60°C (14°F to 140°F)
STORAGE TEMPERATURE -20°C to +70°C (-4°F to -158°F)
HELMET MATERIAL High Impact Polyamide Nylon
TOTAL WEIGHT 920g
MINIMUM AMPERAGE REQUIRED 5A
MINIMUM FLOW 150-220 l/min
PROTECTION AND NOISE LEVEL TH2 P, NPF 20, 65db
LI ION BATTERY LIFETIME 350 Charging Cycles
ONE CHARGING CYCLE 3 to 4 hours
BATTERY OPERATING TIME AFTER CHARGE 6 to 8 hours
BELT SIZE 80 – 100 cm
RECOMMENDED WORKING TEMPERATURE 0 to 40°C
RECOMMENDED WORKING HUMIDITY 20 to 80% RH
SELECTION Air Respiratory System
TYPE Light Reactive Airfed Unit

Additional information

Standards

BS EN 166, BS EN 175, BS EN 379